Presents the up-to-date information on the state of materials fromelectronic, magnetic, and photonic materials, light metals,materials processing and manufacturing, and structural materialswhich are of invaluable benefit to the global industry.
Autorentext
Headquartered in the United States but international in both its membership and activities, The Minerals, Metals & Materials Society (TMS) is a rare professional organization that encompasses the entire range of materials and engineering, from minerals processing and primary metals production to basic research and the advanced applications of materials.
Zusammenfassung
Presents the up-to-date information on the state of materials from electronic, magnetic, and photonic materials, light metals, materials processing and manufacturing, and structural materials which are of invaluable benefit to the global industry.
Inhalt
Supplemental Proceedings: Volume 3: General Paper Selections
General Abstracts: Electronic, Magnetic and Photonic Materials Division.
Session I.
Investigation of Electronic Properties for Nano-Titania/Metal-Ion-Doped Titania Semiconductor Prepared by Sol-Gel Methods (L. Liau, and C. Ma).
Structure and Magnetic Properties Characterization of Electrodeposited Co37Fe63 Alloys Containing Oxygen for Magnetic Recording Applications (S. Elhalawaty, R. Carpenter, J. George, andS. Brankovic).
Tungsten Doping Effect on Thermoelectric Properties of Heusler Fe2VAl Alloy(H. Morishita, M. Mikami, K. Ozaki, and K. Kobayashi).
Session II.
Tatalum Nitride for Efficient Visible-Light-Driven Photocatalyst (Z. Wang, J. Wang, L. Liu, K. Huang, J. Hou, and H. Zhu).
Failure Mechanism of Electrode in Crystalline Photovoltaics (C. Oh, N. Park, C. Han, and W. Hong).
Synthesis of Nano-Sized Tantalum Nitrides with Various Morphology (L. Liu, C. Ma, Z. Wang, K. Huang, S. Jiao, and H Zhu).
Development of New Transparent Conductive Material of Mg(OH1-xCx)2 (x = 0.1-0.35) by Magnetron Sputtering(T. Honjo, and T. Kuji).
Synthesis of Ultrafine Single Crystals and Nanostructured Coatings of Indium Oxide from Solution Precursor (N. Pentyala, R. Guduru, P. Mohanty, and E. Shnerpunas).
Reliability of Wedge Wire Bonds Subjected to Ultrasonic Welding and Thermal Cycling (A. Saigal, M Zimmerman, and J. Battaglia).
General Abstracts: Light Metals Division.
General Light Metals.
Determination of Heat Treatment Effect on 6XXX Series Aluminum Foams by Design of Experiment (D. Deniz Polat, B. Ozkal, and O. Keles).
Effect of Reacted Layer on Galvanic Corrosion Phenomenon at Interface Between Ti Dispersion and Mg-Al Alloy (K. Kondoh, N. Nakanishi, R. Takei, andJ. Umeda).
Compressive Capacity and Fracture Mechanism of Aluminum Foam (H. Hao, G. Lu, M Diop, H. Dong, and X. Zhang).
LiAl Alloy Prepared by Bulk Mechanical Alloying (T. Honjo, and T. Kuji).
Metal Matrix Composites.
Preparation and Characterization of Cast Hypereutectic Al-20wt.%Si-4.5wt.%Cu Nanocomposites with A12O3 Nanoparticles(H. Choi, andX. Li).
An Investigation of Nanoparticle Wetting, Grain Refinement and Mechanical Property Enhancement in Aluminum Matrix Nanocomposites (M. De Cicco, D. Wang, and X. Li).
Stability of Nanoparticle Dispersion and Property Enhancement in Aluminum Matrix Nanocomposites during Repeated Casting Cycles (D. Wang, M. De Cicco, andX. Li).
Preparation Process of Aluminum Foam Reinforced by Carbon Fibers (H. Luo, Y. Liu, P. Chen, and Z. Zhao).
Influence of Processing Parameters on Distribution of Fibers in Cast Aluminium Matrix (P. Yan, G. Yao, J. Shi, and X. Sun).
Primary Production and General Issues.
A Model for the Collapse of the World Trade Center (C. Simensen).
Analysis on the Market Developing Conditions of Prebaked Carbon Anodes for the Aluminium Industries (G. Lang, C. Fu, R. Logan, and Y. Li).
Removal of Fluoride from Waste Water of Aluminum Smelter by Aluminum Ion Loaded Ion Exchange Resin (B. Padhi, and A. Sharma).
Corrosion Behavior of Cermet Anodes in Na3AlF6-K3AlF6-Based Baths for Low-Temperature Aluminum Electrolysis Cells(G. Wang, X. Sun, W. Wang, D. Wang, and Y. He).
Preparation of Al-Mg Alloys from MgO in KCl-MgF2-LiF Electrolyte by Molten Salt Electrolysis Method (F. Yang, S. Yang, X. Hu, Z. Wang, Z. Shi, and B. Gao).
General Abstracts: Materials Processing and Manufacturing Division.
Casting, Surface Modification, and Powder Processing.
Calcium Silicate-Graphite-Compound, a New Material for the Flow Control of Liquid Aluminum Alloys (W. Huetiner, T. Hoelscher, M. Quackenbush, and R. Smith).
Influence of a Direct Current on the Solidification Behavior of Pure Aluminum (Y. Zhang, C. Song, L. Zhu, H. Zheng, and Q. Zhai).
Influence of Heating Effect on the Solidified Structure of Pure Aluminum by Electric Current Pulse (Z. Yin, B. Li, Y Gong, andQ. Zhai).
Manufacturing Methods and Properties of Powder-Based Parts with Inherently Saved Information (B. Behrens, N. Vahed, F. Lange, and E. Gastan).
Microstructure and Mechanical Properties of Al Based Composite Coatings Produced by the Cold Gas Dynamic Spraying Process (0, Meydanoglu, M, Baydogan, E. Kayali, and H. Cimenoglu).
Optimization of Fiber Laser Produced Hastelloy C-276 Single Track Clad (P. Leggett, P. Balu, R. Kovacevic, andS. ...